Builders love one-piece fiberglass tub enclosures because they're cheap and fast to install before the walls go up. Homeowners discover the catch years later: the unit can't come out without cutting it apart and opening the walls around it. In Irvine's 1990s and 2000s villages, from Westpark and Northwood to Woodbury and Portola Springs, that means thousands of dollars of demolition for a surface problem.
Fiberglass enclosure reglazing takes a different approach. We repair the spider cracks, chalky gel coat, soft floor and worn-through spots, then spray the tub, walls, ledges and soap dishes as one seamless, high-gloss surface. The enclosure looks new, the walls stay closed, and you're showering again in 24 hours.
Enclosures we reglaze in Irvine
- One-piece fiberglass tub-shower units
The standard 60-inch alcove unit in most Irvine tract homes and condos, refinished tub, walls and ceiling lip as one piece.
- Acrylic tub surrounds
Multi-piece acrylic and ABS surrounds, with seams sealed under the coating.
- Fiberglass shower stalls
Stand-up one-piece units, including the pan and built-in seat.
- Soft or cracked tub floors
Reinforced with an inlay or structural repair before coating so the floor is solid again.
- Garden and corner fiberglass tubs
Large master-bath fiberglass tubs refinished inside and out.
What fiberglass enclosure reglazing fixes
Fiberglass fails in predictable ways, and we fix all of them before coating:
- Chalky, faded or yellowed gel coat
- Spider cracks and hairline cracks
- A soft, flexing or cracked tub floor
- Worn-through patches where the fiberglass shows
- Stubborn stains and scratches from abrasive cleaners
- Dated almond, bone or beige units
- Peeling or bubbling from a previous DIY refinish kit
Guaranteed in writing
Every enclosure carries a 2-year written warranty
Your reglazed fiberglass tub and surround is covered against peeling, bubbling and loss of adhesion for two full years. Fiberglass needs proper etching and priming to hold a coating, which is exactly why hardware-store kits fail and ours doesn't.
Why Irvine homes have so many fiberglass enclosures
Irvine grew fast from the 1980s onward, and the builders who put up Westpark, Northwood, Oak Creek, Woodbury, Cypress Village, Stonegate and the Great Park neighborhoods used one-piece fiberglass and acrylic units in most secondary bathrooms. Thousands of them are now 15 to 30 years old and showing it.
Because the unit is built into the framing, replacement means drywall, possibly tile, plumbing and a permit. For condo and townhome owners, that also means HOA approval and weeks of contractor traffic. Reglazing is one quiet visit with nothing going to the landfill, which is why it's the standard fix for these units across Irvine.
We're based in Irvine and handle fiberglass tub and shower enclosure reglazing in every village, including Woodbridge, Turtle Rock, Northwood, Westpark, Woodbury, University Park, Great Park Neighborhoods, Quail Hill, Portola Springs, Cypress Village, Orchard Hills, Oak Creek and the rest of the city (ZIP codes 92602, 92603, 92604, 92606, 92612, 92614, 92617, 92618, 92620). We also serve Tustin, Costa Mesa, Newport Beach, Lake Forest, Laguna Hills, Aliso Viejo, Mission Viejo, Santa Ana, Orange and the rest of Orange County, usually with appointments within a few days.
Reglazing vs. replacing a fiberglass enclosure in Irvine
| Reglazing with us | Replacement | |
|---|---|---|
| Time | 4 to 6 hours on site, ready in 24 hours | 1 to 3 weeks: cut-out, wall repair, new unit, tile or surround |
| Typical cost | A fraction of replacement, usually 70 to 80% less | $3,500 to $9,000+ including demolition and wall repair |
| Walls and framing | Untouched | Opened to remove and install the unit |
| Permits and HOA | None needed | Usually required |
| Warranty | 2-year written warranty | Varies by contractor |
See the full breakdown on our save by reglazing in Irvine page.